The importance and methods of Corin column maintenance


The maintenance methods for Colin columns are very important, but if the methods are incorrect, there will still not be much effect. In other words, only reasonable maintenance can help extend the service life of the Colin column. Even simple oiling requires very specific methods. A Colin column is a rod-like component installed on machinery or buildings, playing a traction role. The principle is to balance the sliding of the template and withstand the tension caused by clamping. It is an important component of the injection molding industry.

The maintenance methods for Colin columns are crucial; however, incorrect methods will not yield significant results. In other words, only proper maintenance can help extend the lifespan of the Colin column. Even simple oiling requires specific methods. A Colin column is a rod-like component installed on machinery or buildings, playing a traction role. Its principle is to balance the sliding of the template and withstand the tension caused by clamping. It is a vital component in the injection molding industry.
The slider is one of the accessories of the Colin column and forms a linear guide rail with it. Generally, each slider bearing has an oiling hole on one side; therefore, simply injecting an appropriate amount of machine oil into this hole is sufficient. In the clamping mechanism, the performance of the Colin column directly affects the system's rigidity and stability. Only by improving the structural characteristics of the Colin column can the system's rigidity and stability be effectively enhanced.
However, there are exceptions. For certain Models that cannot be oiled normally, a small hole needs to be drilled in the middle of the Colin column, which is then used to fill the product. This solves the oiling problem without affecting other components or the entire system.
In the design, abrupt changes in shaft diameter must be avoided. At steps or undercuts, try using larger fillet radii transitions, choose materials with better overall performance, and special treatments should not only address the surface hardness (wear resistance) of the threads but also attempt to reduce surface stress concentration, improve surface finish, and minimize stress damage. When problems arise, promptly analyze the causes; do not unilaterally increase the clamping force. If modules are found to be uneven, they should be ground smooth. Ensure processing accuracy, especially when assembling or after disassembling nuts, be sure to adjust the length of the four tie rods.

Latest Information


Zhanwang Machinery Co., Ltd., Dongguan

Dongguan Zhanwang Machinery Co., Ltd. is a manufacturer and supplier of various precision mechanical parts, including rubber and plastic machinery parts, pneumatic and hydraulic machinery parts, precision shafts, piston rods, standard chrome-plated bars, guide columns, uprights, guide pillars, rollers, etc. We provide surface treatments such as super mirror polishing, hard chrome plating for different specifications of precision mechanical parts and various molds. We also offer additional surface treatments such as tempering, medium and high-frequency quenching, nitriding, and blackening for mechanical parts. Our factory is equipped with large CNC lathes, ordinary lathes, external cylindrical grinders, centerless grinders, and milling machines, enabling us to process and manufacture various special mechanical parts. We offer free pick-up and delivery with competitive Price.


Summary of Experience with Failed Colin Column Balance Adjustment

Analyzing the causes of errors and summarizing lessons learned during work is an important way to improve work efficiency. Fault case: A Hetian injection molding machine's Collin column broke. The Collin column was replaced and the balance was adjusted, without needing any special tools.


Injection Molding Machine Accessories: Detailed Analysis of Common Temperature Problems!

Injection molding machine accessories. In co-ordinated control, the direction of the temperature sensor in the mold is critical. When placing the temperature sensor, the user must consider its shape, structure, and the direction of the cooling channels. In addition, the temperature sensor cannot be placed arbitrarily; it should be placed in an area that has a critical effect on the quality of the injection molded product. There are many ways to connect one or more high-temperature mold temperature controllers to the controller.


Injection Molding Machine Accessories: Standard Maintenance for Injection Molding Machines

Injection molding machine accessories. Everyone should formulate appropriate daily, monthly, and annual maintenance plans based on the condition of the equipment itself, and carefully implement them for each machine according to the plan. Before using the equipment every day, we should check whether each part of the equipment is normal, such as whether the machinery is working normally, whether the heating conditions of each part are normal, whether the circulating water pipes are leaking, whether the emergency stop button can cut off the motor power supply, etc.


What should be noted when repairing a faulty piston rod?

Piston rod failure is normal. The key is to pay attention to the precautions during specific maintenance. If non-professionals perform maintenance, many problems may arise. If possible, choose professional personnel. Maintenance efficiency and its own use value will be higher. We recommend that everyone should understand the following precautions when understanding piston rod maintenance.


What are some applications of piston rods?

In fact, even if we don't mention it, everyone should know quite a bit about piston rods. Of course, to ensure the efficiency of the piston rod, we must guarantee its performance and quality. If more friends are interested in this field, you can also Tel us to discuss your views, I believe this will be helpful to our work.


Connecting structure of piston rod and piston and how to choose piston rod

Piston rods offer significant advantages in practical applications, and the connecting rod structure of the piston is also unique. When used in combination, it is essential to carefully select hydraulic cylinders that demonstrate good operating and production performance. Such products will be highly reliable. The connection structure between the piston rod and piston, and the manufacturing method of the hydraulic cylinder with this piston rod, are essentially the same.


What does the mold pull rod spacing mean in the injection molding machine parameters?

The actual usable area of the template: the greater the distance between the ejector rods, the greater the actual width and height of the grinding tools that can be accommodated. Because injection molding machines need to install plastic injection molds between the moving template and the fixed template, plastic products can be processed. If the mold is to be installed between the two templates, it must pass through two adjacent ejector rods, so the shape of the mold must be smaller than the spacing between the ejector rods.

Rich experience in production practice, to provide you with reliable quality products